Skip to content

Redefining Luxury in Every Detail.

Gold Bathroom


How to Fix a Dripping Tap in Your Gold Bathroom UK: A Comprehensive DIY Guide

by Elena M 01 Jan 2024
How to Fix a Dripping Tap in Your Gold Bathroom UK: A Comprehensive DIY Guide


A dripping tap in a gold bathroom can transform from a minor annoyance to a significant concern, especially in the quiet of the night.

Contrary to popular belief, fixing a dripping tap in gold bathrooms doesn't necessarily involve a complete overhaul of your fixtures.

Whether it's a gold bath tap, gold pillar taps, or any gold bathroom accessories UK, a dripping tap is often a simple DIY fix.

This guide will take you through the process, explaining the types of taps, the tools you'll need, and step-by-step instructions for fixing that pesky drip.

Understanding Your Bathroom Tap

Bathroom taps, especially those in luxurious gold bathrooms, come in various designs and mechanisms. Generally, there are two types: traditional and monobloc. Each type has specific components that, when worn out, can cause dripping.

Traditional Taps

Traditional taps are common in many bathrooms, often featuring gold taps for bathroom aesthetics. These taps typically drip due to a worn-out rubber seal or washer. The washer is a crucial component that forms a water-tight seal, preventing water from dripping when the tap is turned off.

Monobloc Taps

Monobloc taps, frequently found in modern gold bathroom accessories UK, usually have a single handle and are known for their sleek design. These taps use ceramic cartridges instead of rubber washers. The ceramic discs control the flow and mix of hot and cold water. Over time, these cartridges can wear out or become damaged, leading to a drip.

Identifying the Cause of the Drip

 The first step in fixing a dripping tap is identifying the cause. If your tap is a traditional model, the culprit is likely a worn washer. For monobloc taps, the issue could be a worn-out ceramic cartridge. In some cases, especially with traditional taps, worn O-rings can also cause leaks.

Tip: A quick way to identify the type of tap is by its operation. Traditional taps typically require multiple turns to open, while monobloc taps usually operate with a quarter or half turn.

Tools and Materials

To fix a dripping tap, you will need a few basic tools and replacement parts. The required tools are often already available in a typical household toolkit.


  • An adjustable spanner
  • A cross-headed screwdriver
  • A flat-head screwdriver (for O-ring replacement)
  • A pair of scissors (for cutting off old O-rings)


  • Replacement washer or ceramic cartridge
  • Replacement O-ring (if necessary)
  • Lubricant (like WD40) for easing tight components

Important: Always turn off the water supply before starting any repair work on taps. This prevents water from gushing out when you disassemble the tap.

Tip: Placing the plug in the sink during the repair process prevents small parts like screws or washers from accidentally going down the drain.

Step-by-Step Repair Guide

dripping tap

Step One: Disassemble the Tap

  • Remove Decorative Caps or Covers: Start by removing any decorative elements to access the internal components. These can usually be unscrewed by hand or gently pried open with a screwdriver.
  • Unscrew the Tap Handle: Once the decorative elements are removed, you’ll see a screw that holds the handle in place. Use a screwdriver to loosen and remove this screw.
  • Take Apart the Tap: Carefully disassemble the tap, keeping all parts in order. This will make reassembly easier.

Step Two: Identify and Replace the Faulty Component

For Traditional Taps:
  • Locate the hexagonal nut and use an adjustable spanner to unscrew it. This will expose the washer.
  • Remove the old washer and replace it with a new one. Ensure the size and type match the original.
  • For Monobloc Taps:
  • After removing the handle, you’ll find the ceramic cartridge held in place by a hexagonal nut.
  • Use the spanner to loosen and remove the nut, then replace the cartridge.
  • Step Three: Reassemble the Tap

    • Put the Tap Back Together: Carefully reassemble the tap in reverse order. Ensure each part is clean and properly aligned.
    • Tighten, But Not Too Much: When reassembling, be careful not to overtighten components, as this can damage them and lead to further leaks.

    Step Four: Check for O-Ring Damage

    • If the tap continues to drip after replacing the washer or cartridge, check the O-ring. This is a common issue with traditional taps.
    • Replace the O-ring if it appears worn or damaged. Use a flat-head screwdriver to remove the old O-ring and slide the new one into place.

    Tip: Applying some lubricant can help in removing tight components or easing the installation of new parts.

    Final Steps and Testing

    Once you have reassembled the tap, it's time to test your work:

    • Turn On the Water Supply: Slowly turn on the water supply and watch for any immediate leaks.
    • Test the Tap: Turn the tap on and off several times, checking for drips.


    Fixing a dripping tap in a gold bathroom is a manageable task for most DIY enthusiasts. Whether you’re dealing with gold pillar taps, chrome and gold bathroom taps, or any other luxurious gold bathroom accessories UK, this guide provides the knowledge and steps needed to tackle the job confidently.

    Do you have any additional tips or experiences fixing dripping taps in gold bathrooms? Share your insights and help others perfect their DIY skills in maintaining luxurious gold bath taps !

    Discover more on our Gold Bathroom UK website!

    Prev Post
    Next Post

    Thanks for subscribing!

    This email has been registered!

    Shop the look

    Choose Options

    Edit Option
    Back In Stock Notification
    this is just a warning